Specifications

• Weight: 4.5 lbs (2.04 kgs), with batteries.
• Size: 8.5W x 6.5H x 2.5D in (216 x 165 x 70mm).
• Operating Temperature: 14 to 140F (-10C to 60C).
• Keyboard: Membrane switch with 21 tactile keys.
• Case: Extruded aluminum body with nickel plated aluminum end caps (gasket sealed).
• Display Views: RF (full wave view), +/- Rectified (half wave view), Digits, or split screen combination (wave plus large digits).
• Environmental: Meets IP65 requirements.

Connections

• USB: Direct USB 1.1 PC connectivity.
• Power Connector: 12v @ 2amps, adapter 100-240 VAC, .7 Amps, 50-60 Hz.5 Pin Lemo (includes):RS232Output – RS232 PC serial interface.Alarm Outputs – Two independent alarm outputs triggered by the gates.Analog Out – Proportional outputs (amplitude or distance), 0-10 volts.
• Transducer Connectors: Two LEMO 00 connectors.

Memory

• Log Formats: Grid (Alpha Numeric).
• Capacity: 4 Gb internal & up to 64 Gb External SD slot.
• Screen Capture: Tagged interface file (.tif) capture for quick documentation.
• Custom Setups: 64 user configurations.

Power Source

• Lithium Ion Pack: 10.8v, 2 amp hrs, typical operation 18hrs.
• Battery Backup: Emergency battery backup. Six 1.5V alkaline, 1.2V AA Nicad cells, 1.2V AA NI-MH, or other other equivalent power source.
• Battery life (continuous use): Alkaline (12 hrs), Nicad (5hrs), and NI-MH (12hrs), with default settings.

• Display: Blanview sunlight readable QVGA TFT color display (320 x 240 pixels). Viewable area 4.54 x 3.40 in (115.2 x 86.4 mm), or 5.7 in (144.78 mm) diagonal. 16 color pallete, multiple color options and variable brightness.
• Screen Refresh Rate: 60Hz.
  Timing: Precision TCXO timing with single shot 100 MHz 8 bit ultra low power digitizer.
• Pulser Types: Spike, Square Wave & Tone Burst.Pulser Voltage: 100 – 400v.
• Pulser Voltage: 100 – 400v.
• Pulse Width: Selectable step options Spike, Thin, Wide, HV Spike, HV Thin, HV Wide, TB .5MHz, TB 1MHz, TB 2MHz, TB 5MHz, TB 10 MHz. Spike 40 ns, Square Wave 80 to 400 ns, Tone Burst 50 ns to 1 microsecond.
• Gain: 0 to 110dB with 0.2dB resolution. Manual and AGC control.
• Damping: 50, 75, 100, 300, 600, & 1500 ohms.
• Frequency Band: Broadband 1.8 – 19 MHz (-3dB) filter.
• Horizontal Linearity: +/- 0.4% FSW.
• Vertical Linearity: +/- 1% FSH.
• Amplifier Linearity: +/- 1 dB.
• Amplitude Measurement: 0 to 100% FSH, with 1% resolution.
• Delay: 0 – 999.999in (25,400mm) at steel velocity.
• Measurement Gates: Three independent gates depending on measurement mode selected, with audible and visual alarms. Amplitude 5-95%, 1% steps.

Features

• Setups: 64 custom user defined setups; factory setups can also be edited by the user.
• Auto Set: Automates the detection, scope, and display setting process for each individual bolt.
• Gates: Three measurement gates, depending on measurement mode used, with adjustable start and threshold.
• Alarm Limits: Adjustable Hi/LO tolerances with visual LED鈥檚 and audible beeper. Hardware alarm outputs (accesory cable required).
• Field Calibration: Vector or Regression correction curve for increased accuracy using Load & Stress.

• Units: English (in), Metric (mm), or Time (碌s).
• Velocity: 0.0492 to .5510 in/碌s (1250鈥?3995 m/s).
• Measurement Modes: Pulse-Echo (P-E), Echo-Echo (E-E), or Echo-Echo-Echo (E-EV).
• Measurement Range: 1 to 999.999in (2540cm) in pulse-echo(P-E) measurement mode. Range will vary using multi-echo modes – dependent on material type and consistency.
• Detection: Zero Crossing.
• Resolution: +/- 0.00001 in (0.0001 mm).
• Calibration: Automatic, Fixed, Single or Two-Point zero calibration options.
• Quantities:Time – Nanoseconds.Elongation – Change in length (inches/millimeters).Load – Force load applied (pounds KIP or megapascals MPa).Stress – Force for unit area stress applied (inches per inch or millimeters per millimeter).%Strain – Ratio of elongation to effective length.
• Bolt Materials: Select types from a preset or custom list.

Transducers

• Transducer types: Single element – 1 MHz to 10 MHz frequencies, and 1/8鈥?to 1鈥?diameters. Magnetic & Non Magnetic options available.
• Glue-On: Available for short bolts with minimal/short elongations to eliminate transducer placement errors.
• Connectors: Microdot, Lemo 00, or BNC options depending on the transducer model selected.
• Custom Transducers: Available for special applications.

Certification

• Factory calibration traceable to NIST & MIL-STD-45662A.

Warranty

• 2 year limited

注：本站商品信息均来自于合作方，其真实性、准确性和合法性由信息拥有者（合作方）负责。本站不提供任何保证，并不承担任何法律责任。

牛器网价：牛器网价为商品的销售价，是您最终决定是否购买商品的依据。

划线价：商品展示的划横线价格为参考价，并非原价，该价格可能是品牌专柜标价、商品吊牌价或由品牌供应商提供的正品零售价（如厂商指导价、建议零售价等）或该商品在牛器网平台上曾经展示过的销售价；由于地区、时间的差异性和市场行情波动，品牌专柜标价、商品吊牌价等可能会与您购物时展示的不一致，该价格仅供您参考。

折扣：如无特殊说明，折扣指销售商在原价、或划线价（如品牌专柜标价、商品吊牌价、厂商指导价、厂商建议零售价）等某一价格基础上计算出的优惠比例或优惠金额；如有疑问，您可在购买前联系销售商进行咨询。

异常问题：商品促销信息以商品详情页“促销”栏中的信息为准；商品的具体售价以订单结算页价格为准；如您发现活动商品售价或促销信息有异常，建议购买前先联系销售商咨询。